It's used to pipeline
Material:brass H62
Material specification:∅25×64
Surface treatment:chrome plated
Properties of brass H62
H62 brass represents ordinary brass with an average copper content of 62%,ordinary brass is based on the addition of other elements of copper alloy be called special brass and it is still represented by "H",followed by the chemical symbol and average composition f other added elements.Such as H62 that the copper content is 60.5%~63.5%,remaining content is zinc.HA59-3-2 indicates that its copper content is 57%~60%,aluminum content about 2.5%~3.5%,nickel content is 2%~3%,and the remaining content is zinc.There are three kinds of brass that are divided into ordinary brass,special brass and cast brass.Cast brass begins with ZCu followed by the symbol of other elements and their average content.
Ordinary brass has good mechanical properties,it has good plasticity in the cold state,better plasticity in the hot state.Has good machinability,easy brazing and welding,corrosion resistance,but it is easy to produce crack.In addition,the price is cheap and widely used in a common brass variety.H62 brass is much harder at room temperature in β phase than in a phase,so it can be used for parts that bear large loads."a+"two-phase brass can be hot machining above 600℃.Microstructure of a+β two-phase brass:a is a bright white solid solution and β is a CuZn-based ordered solid solution.
It can make all kinds of tensile and bending manufacturing stress parts,such as pins,rivets,washers,nuts,ducts,barometer springs,screen mesh,radiator parts,etc.
Mechanical property
Strength of extension(Rm N/mm2）：385.0
Extend rate(A%):15.0
Chemical component Cu:60.5-63.5 Ni:0.5 Fe:0.15 Pb:0.08 Zn:remaining
Impurity:0.5
Mechanical property:（σb/MPa)410-630
Elongation（δ10/%）≥10
Vickers hardness:(HV)105-175
Thickness≥0.3）Note:thickness 0.3-10
Processing technic
The quantities of tools:9 tools
Tool Type
35°round turning tool
2MM cut-off tool
∅7.1 drill bit
∅8 boring tool
∅8 inside threading tool
∅5.5 drill bit
1/4-32 screw tap
∅8 milling cutter
∅1.5 drill bit
∅1.5 milling cutter
According to the drawing to analysis that the copper valve parts haven't special precision requirements in the shape and position tolerance.Therefore,we choose the direction of 5/8 thread of the parts as the priority for machining,because there is a requirements of R0.5 Angle in this direction.In order to fillet R0.5 Angle and the cylindrical inclined plane and end face processed surface connection relationship is more perfect.
Use 35°round turning tool machining parts shape,then use ∅7.1 drill bit, ∅8 boring tool to machining ∅7.1 and 5/8 x18 thread bottom hole.
Use ∅8 inside threading tool to machining 5/x18 thread,then use ∅1.5 drill bit,∅1.5 milling cutter to machining hole of ∅1.5×3.5 size,then use ∅5.5 drill bit,1/4-32 tap screw and ∅8 milling cutter to machining ∅9.5 and 1/4-32 thread,then cut off the parts use 2mm cut off tool.
It is necessary to custom clamp before processing at both end,male thread 5/8×18 length is 11mm.As following picture shows:
The reason is that the surface is inclined plane of this parts and there is no clamping condition.So it only can assembly with 5/8×18 internal thread which has been machined with the 5/8×18 external thread of the fixture.Then processing of the remaining part,which not only ensure the repeated positioning error of the parts but also improved the processing efficiency.
Use 35°round turning tool to machining total length 59mm,then use ∅7.1 drill bit and ∅8 boring tool to machining 1/2×20 thread.Finally make surface treatment of chrome plated.
Please refer to finished parts as below:
Recommended Products:Customized Stainless Steel CNC turning parts
Link to this article：Valve Body
Reprint Statement: If there are no special instructions, all articles on this site are original. Please indicate the source for reprinting.：Cnc Machining，Thank
